Product ID:EUTECROD 1900
MSDS Date:11/12/1991
FSC:3439
NIIN:00-064-9899
MSDS Number: BVFJV

EUTECTIC CORP

40-40 172ND ST
FLUSHING, NY 11358-2799
US

Emergency Phone: 718-358-4000

Info Phone: 718-358-4000

Cage: 72271

EUTECTIC CORP

CHARLOTTE, NC 28273 US

Telephone: 704-527-9800/ 800-221-1433

Cage: 72271

MAGNESIUM

CAS: 7439-95-4

RTECS: OM2100000

OSHA PEL 15 MG/M3 (MFR)

ACGIH TLV: 10 MG/M3 (MFR)

ALUMINUM (SARA III)

CAS: 7429-90-5

RTECS: BD0330000

Fraction By Weight: 5-10%

OSHA PEL 15 MG/M3 DUST;5 FUME

ACGIH TLV: 10 MG/M3 DUST

DIOXIDE, NITROGEN OXIDES & CERTAIN INERT GASES USED

RTECS: 9999999ZZ

FEVER, HEAD & MUSCLE ACHE, TIGHTNESS OF

RTECS: 9999999ZZ

VOMIT. SYMPS USUALLY OCCUR W/IN SEVERAL HRS AFTER

RTECS: 9999999ZZ

SYMPS DEVEL AFTER WELDING OPERATION. GEN NUISANCE

RTECS: 9999999ZZ

PRDCE PARTICULATE IRRIT. EXCESSIVE INHAL CAN PRDCE

RTECS: 9999999ZZ

INHAL MAY CAUSE METAL FUME FEVER.

RTECS: 9999999ZZ

ULTRAVIOLET LIGHT CAN INJURE EYES & BURN SKIN.

RTECS: 9999999ZZ

FILTER LENS. PROVIDE PROT SCREENS & FLASH GOGGS IF

RTECS: 9999999ZZ

IS TOO DARK TO SEE WELD ZONE, THEN GO TO NEXT

RTECS: 9999999ZZ

PVNT INJURY FROM RADIATION, SPARKS &

RTECS: 9999999ZZ

HATS AS WELL AS DARK, PROTECTIVE CLOTHING.

RTECS: 9999999ZZ

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:YES Ingestion:NO
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:LITTLE/NO HAZS EXIST FOR ARC WELDING
BRAZING RODS BEFORE THEY ARE USED IN WELDING PROCESS. INHAL:FUMES,
GASES & DUSTS CAN BE DANGEROUS TO YOUR HLTH. CERTAIN MED STUDIES
HAVE SUGGESTED THAT LUNG DMG CA N RSLT FROM OVEREXP TO THESE FUMES.
SHORT TERM OVEREXP MAY RSLT IN DIZZ, NAUS OR DRYNESS/IRRIT OF
NOSE,(EFTS OF OVEREXP)
Explanation of Carcinogenicity:NOT RELEVANT
Effects of Overexposure:HLTH HAZ:THROAT/EYES. EXCESSIVE OVEREXP MAY
CAUSE BRONCH ASTHMA, LUNG FIBROSIS, PENUMOCONIOSIS/SIDEROSIS (IRON
DEPOSITS IN LUNG). METAL FUME FEVER CAN BE CAUSED BY INHAL OF
CERTAIN METALLIC CMPDS DURI NG WELDING, HEATING, BRAZING,
SOLDERING/CUTTING OPERATIONS. SYMPS ARE SIMILAR TO FLU TYPE
SICKNESS INCL CHILLS, (ING 4)
Medical Cond Aggravated by Exposure:AGGRAVATION OF PREEXISTING
RESPIRATORY OR ALLERGIC CONDITIONS MAY OCCUR IN SOME WORKERS.

First Aid:INHAL:MOVE VICTIM TO FRESH AIR SOURCES. CONTACT MD & ADVISE
ON INGREDIENTS. SKIN:THORO WASH HANDS/AFFECTED AREAS W/SOAP & WATER
TO REMOVE ALL RESIDUE. IF RASH/BURN DEVELOPS, CONSULT MD. EYE:THORO
FLUS H W/WATER FOR AT LST 15 MINS TO REMOVE ALL RESIDUE. OBTAIN
PROMPT MED ADVISE & CHEMICAL AIDS. ADVISE MD OF INGREDIENTS.
INGEST:CALL MD &/OR LOCAL POISON CONTROL CENTER. ADVISE OF
INGREDIENTS.

Extinguishing Media:CO*2, DRY CHEMICAL FOAM TYPE.
Fire Fighting Procedures:USE NIOSH/MSHA APPROVED SCBA & FULL PROTECTIVE
EQUIPMENT . TOXIC FUMES MAY BE PRODUCED.
Unusual Fire/Explosion Hazard:GENERALLY NONFLAMM; WELDING ARC, SPKS &
FLAMES CAN IGNITE COMBUSTS & FLAMMS. CANS, UNDER PRESS & FLAMMS MAY
EXPLODE. REFER TO ANSI Z491. FOR FIRE PVNT (SUPDAT)

Spill Release Procedures:NONE SPECIFIED BY MANUFACTURER.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling and Storage Precautions:TRAIN WORKERS NOT TO TOUCH LIVE
ELECTRICAL PARTS & TO INSULATE THEMSELVES FROM WORK & ELECTRICAL
GROUND. USE ADEQUATE VENTILATION. HANDLE W/CARE.
Other Precautions:TRAIN WELDER TO KEEP HIS/HER FACE AWAY FROM FUME/DUST
PLUME. PLEASE READ & UNDERSTAND PROD LBL INFO FOR PROPER PROCS &
USE. SEE ANSI Z49.1 "SFTY IN WELDING & CUTTING" BY AWS & OSHA PUB
2206 (29 CFR 19 10) FOR MORE DETAIL.

Respiratory Protection:IF WORK STATION IS NOT PROPERLY VENTILATED TO
EXHAUST ALL FUMES, VAPORS & DUSTS BELOW THE RECOMMENDED EXPOSURE
LIMITS, USE A NIOSH/MSHA APPROVED RESPIRATOR.
Ventilation:USE ENOUGH GENERAL VENT & LOCAL EXHAUST AT WORK SITE TO
KEEP ALL FUMES & DUSTS FROM WORKER'S BRTHG ZONE & GENERAL AREA.
Protective Gloves:WELDER'S GLOVES.
Eye Protection:WEAR HELMET & FCSHLD W/APPROP (ING 10)
Other Protective Equipment:EMER EYE WASH & DELUGE SHOWER WHICH MEETS
ANSI DESIGN CRITERIA . WEAR HAND, HEAD & BODY PROT WHICH HELP
TO(ING 12)
Work Hygienic Practices:NONE SPECIFIED BY MANUFACTURER.
Supplemental Safety and Health
EXPLO HAZ:DURING USE OF WELDING & ALLIED PROCESSES. HAZ DECOMP
PROD:COATINGS, NUMBER OF WORKERS, CONTAMS IN ATM. FUMES & GASES MAY
VARY IN FORM & PERCENT FROM INGS LISTED. REAS EXPECTED CONSTITUENTS
O F FUME MAY INCL COMPLEX OXIDES OF METALS LISTED. GASEOUS RXN
PRODS MAY INCL OZONE, CARBON MONOXIDE, CARBON (ING 3)

Appearance and Odor:NONE SPECIFIED BY MANUFACTURER.

Stability Indicator/Materials to Avoid:YES
NONE SPECIFIED BY MANUFACTURER.
Stability Condition to Avoid:NONE SPECIFIED BY MANUFACTURER.
Hazardous Decomposition Products:COMPOSITION & QTY OF FUMES & GASES ARE
DEPENDENT UPON METAL BEING WELDED, PROCESS, PROCS, ELECTRODES USED,
(SUPP DATA)

Waste Disposal Methods:DISPOSE OF WASTE MATL, POWDERS, GRINDING OR
FILTER RESIDUES IN ENVIRONMENTALLY SENSITIVE MANNER I/A/W FEDERAL,
STATE & LOCAL REGULATIONS. USE APPROP MEASURES TO KEEP AIRBORNE
DUST LEVELS CNTND I/A/W E XPOS LEVELS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.